Barracuda Control Board Replacement Kit

This is a replacement Barracuda control board and includes all the components that go on the Barracuda control board. This kit comes included in the full Barracuda ROV kit. The replacement kit is only needed if an issue occurs and the Barracuda control board needs to be replaced, or if you want to remove the Barracuda control board so a new group of students can solder and assemble the board.

• Header Connector - 3 position 4 pcs
• Power Cord 18 Ga. (red/black zip cord) 12 inches
• Power Cord 16 Ga. (red/black zip cord) 18 inches
• Barracuda Control Board (Rev 1) 1 pcs
• Barracuda Bluetooth Module 1 pcs
• Reclaimed Wire (18 gauge, red) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, black) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, yellow) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, blue) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, orange) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, white) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, brown) cut to 5" lengths 1 pcs
• Reclaimed Wire (18 gauge, green) cut to 5" lengths 1 pcs
• Voltage Regulator - 9V 1 pcs
• MOSFET N-CH 40V 45mA 2 pcs
• Bi-color LEDs (GRN/RED) 4 pcs
• DIODE SCHOTTKY 20V 1A 2 pcs
• Capacitor - Ceramic 1uf 100v 3 pcs
• Header Connector - 3 position 4 pcs
• Header Connector - 4 position 1 pcs
• Receptacle Connector - 3 position 4 pcs
• Receptacle Connector - 4 position 1 pcs
• Header Connector Terminal strip (50 pin) 1 pcs
• Resistor 1k-ohm 7 pcs
• Resistors 2k-Ohm (small body) 2 pcs
• Resistors 10k-Ohm (Barracuda) 2 pcs
• Mini Blade Fuse Holder - PCB 1 pcs
• 3 Amp Mini Blade Fuse (Violet) 1 pcs
• Shorting jumper (0.1" pitch) 4 pcs
• RELAY GEN PURPOSE SPDT 10A 12V 2 pcs
• Capacitor - Aluminum 220 uf 25v 1 pcs
• Capacitor - Ceramic 1uf 100v 2 pcs
• Capacitor - Aluminum 1000 uf 16v 2 pcs
• Diode 150V 2A 1 pcs
• Mini Blade Fuse Holder - PCB 1 pcs
• 3 Amp Mini Blade Fuse (Violet) 1 pcs
• 7mm Black Heat Shrink [inches] 6 inches
• Radial Inductor 1 pcs
• Bi-color LEDs (GRN/RED) 6 pcs
• Receptacle Connector - 5 position 3 pcs
• Resistor 1k-ohm 5 pcs
• 30 Amp Powerpole Connector Housings (One RED/BLACK bonded pair with two 30amp crimp lugs in a 1x2 bag) (requires 3-PWR-7008-AA-01 Powerpole crimper for installation) 4 pcs
• 45 Amp PCB Contact - Horizontal (Bottom), right angle mount 4 pcs