TriggerFish Control Box Kit (Rev 4) - (Unassembled)

This is for the Triggerfish CONTROL BOX ONLY. The Triggerfish Kit with Thrusters and Tether is available here.

The Triggerfish is an easy-to-construct ROV kit that moves from a switchbox controller to analog joystick control of four motors. This is the Triggerfish control box assembly only; this kit does not include frame materials, the tether, nor thrusters for your ROV.

The control system is housed inside a compact, Seahorse brand protective equipment case. Two joysticks make piloting the Triggerfish ROV easy and logical. Each joystick controls two motors: one joystick controlling forward/reverse and turning, the other joystick controlling up and down, and sideways movement. The joysticks and control boards on the Triggerfish allow speed control; nudging the joystick forward provides slow speed, while pushing the joystick fully provides full-speed movement. The Triggerfish comes video ready (video system sold separately) with two video input channels and easy power out for monitors and cameras. A volt and ammeter, along with multiple LED indicators, display vehicle status and make the Triggerfish easy to troubleshoot. Modular connections mean that Triggerfish control boxes and vehicles are interchangeable.

Detailed assembly instructions are available for the Triggerfish kit, including video lessons, classroom activities, and many more topics here. You will need to register to access our lesson plans; however, registration is free.

Control Box

• Triggerfish Box (Rev 4) (machined yellow box - large hole, no rib) – 1 ea
• Triggerfish Box Plate 1 – 1 ea
• Triggerfish Box Plate 3 – 1 ea
• Triggerfish Box Plate 4 – 1 ea
• Triggerfish Box Sticker – 1 ea
• Terminal Block - 8 Position (Blue) 5.08mm – 1 ea
• Joystick – 2 ea
• Joystick 3 pin connector wire – 2 ea
• Joystick 3-pin Header Connector – 4 ea
• Amp/Volt/Watt Meter for Triggerfish – 1 ea
• TF/UD Power Rocker Switch – 1 ea
• Power Cord 18 Ga. (red/black zip cord) – 30 cm
• Power Cord 16 Ga. (red/black zip cord) – 45 cm
• Heatsink compound – 2, 1g pkg
• Triggerfish Main Control Board (Rev 4) – 1 ea
• Sabertooth Motor Controller with water resistant coating – 2 ea
• Reclaimed Wire (18 gauge, red) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, black) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, yellow) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, blue) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, orange) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, white) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, brown) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, green) cut to 12.7cm lengths – 1 ea

Triggerfish Control Box Hardware Bag

• Steel Phillips Rounded Head Screws 8-32 Thread Size, 1-1/2" Long – 2 ea
• Steel Phillips Rounded Head Screws 8-32 Thread Size, 3/4" Long – 6 ea
• Steel Locknut with External-Tooth Lock Washer Zinc-Plated, 8-32 Thread Size, 11/32" Wide – 8 ea
• Phillips Rounded Head Screws for Sheet Metal Zinc-Plated Steel, Number 4 Size, 1/2" Long – 4 ea

Triggerfish Control Board Component Bag

• Capacitor - Aluminum 220 uf 25v – 1 ea
• Capacitor - Ceramic 1uf 100v – 2 ea
• Capacitor - Aluminum 1000 uf 16v – 2 ea
• Diode 150V 2A – 1 ea
• Mini Blade Fuse Holder - PCB – 1 ea
• 3 Amp Mini Blade Fuse (Violet) – 1 ea
• 7mm Black Heat Shrink Tubing – 15 cm
• Radial Inductor (101) 100uh 1.4A 280 MΩ – 1 ea
• Bi-color LEDs (GRN/RED) – 6 ea
• Receptacle Connector - 5 position – 3 ea
• Resistors 1k-Ω – 5 ea
• 30 Amp Powerpole Connector Housings (One RED/BLACK bonded pair with two 30amp crimp lugs in a 1x2 bag) – 4 sets
• 45 Amp PCB Contact - Horizontal, right angle mount – 4 ea

Triggerfish Control Board Hardware Bag

• Steel Phillips Rounded Head Screws 8-32 Thread Size, 1/4" Long – 4 ea
• Steel Phillips Rounded Head Screws 8-32 Thread Size, 1/2" Long – 4 ea
• Aluminum Hex Standoff - 5/8" x 5/16" x 8-32 – 4 ea

Triggerfish Backplane Board Kit (Rev 4)

• MATE Backplane Board (Rev 3) – 1 ea
• Powerpole Connector Housings (RED/BLACK bonded pair housings only - without crimp lugs) – 1 pair
• Header Connector - 5 position – 3 ea
• 1/4" Quick Connect Female, 14-16 AWG fully insulated – 5 ea
• Power Cord 16 Ga. (red/black zip cord) – 30cm
• Tether Connector - 12 pin - male/female set – 1 ea
• Reclaimed Wire (18 gauge, red) cut to 12.7cm lengths – 2 ea
• Reclaimed Wire (18 gauge, black) cut to 12.7cm lengths – 2 ea
• Reclaimed Wire (18 gauge, yellow) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, blue) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, orange) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, white) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, brown) cut to 12.7cm lengths – 1 ea
• Reclaimed Wire (18 gauge, green) cut to 12.7cm lengths – 1 ea

Tether Connector (12 pin) hardware bag

• Steel Nut (M3 x 0.5 mm Thread) – 4 ea
• Steel lock washer (M3) – 4 ea
• Steel Pan Head Phillips Screw (M3 x 0.5 mm Thread, 12 mm long) – 4 ea

Triggerfish Backplane Component Bag (Rev 4)

• Bi-color LEDs (GRN/RED) – 2 ea
• Resistors 1k-Ω – 2 ea
• Steel Phillips Rounded Head Screws 8-32 Thread Size, 3/4" Long – 4 ea
• Steel Locknut with External-Tooth Lock Washer Zinc-Plated, 8-32 Thread Size, 11/32" Wide – 4 ea
• Nylon spacers for TF-BA Backplane – 4 ea
• BNC Connector Jack, Female Socket - Panel Mount – 2 ea
• Video power jack – 1 ea
• Terminal Block - 4 Position (Black) 3.5mm – 1 ea
• RCA Jack Mono Connector - PCB – 2 ea
• Mini Blade Fuse Holder - PCB – 1 ea
• 15 Amp Mini Blade Fuse – 1 ea
• 45 Amp PCB Contact - Vertical mount, short tail contact – 2 ea

A power supply is not included in this kit. Please check out this link for more power options.