Underwater Robotics --- Educational Kits and Components for Remotely Operated Vehicles (ROVs)
Cart 0
SeaMATE PufferFish ROV Kit (Rev 7)

SeaMATE PufferFish ROV Kit (Rev 7)

$ 200.00 $ 250.00

The PufferFish ROV Kit has now been upgraded to Rev 7 to incorporate the following improvements:

1. The PC board is updated to replace the Amp/Volt Meter wire color labels at the terminal blocks with numbered locations that can serve meters with different wire color configurations by looking up the locations on an included chart.
2. The PC board is updated so that the LEDs for each of the 3 motors are now all in line.
3. The propeller kit now includes a capsule of thread locker. 

 Pre-assembled kits require additional lead time. 






Frame parts are not included in our ROV kits. We recommend buying your PVC frame parts from local suppliers or you can purchase a frame kit from us here: https://seamate.org/products/3-seamate-pufferfish-pvc-frame-kit



SeaMATE ROV kits do not come with a power source.  You will need to provide a power source to power your vehicle.  The SeaMATE store offers three different solutions, depending on your budget and how you intend to use the ROV.  

Power pack with powerpole adapter:

Powerpacks are battery packs that will provide the power you need.  They are often kept in vehicles to jumpstart a car battery if there is a problem.  They will run down over time, but can be recharged easily by plugging them into a wall socket.  A standard power pack should be able to run a PufferFish ROV for 1 to 2 hours.  
The power packs will need an adapter for the powerpole connector to plug into.  This adapter plugs into the cigarette lighter outlet found on the powerpacks, and the Powerpoles plug into the adapter.  The cigarette lighter adapter can be purchased from the SeaMATE Store at:

12 volt Deep-Cycle Marine/RV car battery:

Large lead acid batteries are another way to power the ROV.  MATE recommends the Deep-Cycle Marine / RV battery, as they are designed to be run down and recharged many times (a standard 12 volt car battery is not designed for this).  The battery should be able to run a PufferFish ROV for 4 to 6 hours or you can run 3 ROVs at a time for an hour or more.  The battery will need to be recharged after that.  To recharge a car type battery, you will need to purchase a charger.  
The battery will also need an adapter for the powerpole connector to plug into.   This adapter has Alligator clips that connect to the battery posts on one end and has powerpole connectors at the other end.  The alligator clip adapter can be purchased from the SeaMATE Store at: http://seamate.myshopify.com/collections/all-products/products/alligator-clips-to-powerpole-connector

AC to DC Power Supply:

For a solution that never needs recharging, the MATE Center recommends an AC to DC, 30 amp power supply that plugs into an AC outlet, and provides a constant source of 12 volt DC power that the ROV needs.  This power supply can operate two PufferFish vehicles at once without issue.  
SAFETY NOTE:  Since this converter is being used near water, you MUST plug this converter into a Ground Fault Circuit Interrupter (GFCI) protected outlet, or have a GFCI plug on the end of the converter.  DO NOT PLUG THIS INTO A STANDARD WALL SOCKET WITHOUT GFCI PROTECTION.
MATE also recommends keeping the AC to DC converter in a splash proof container or case.  A small plastic tub turned upside down will work to keep splashes off the power supply.

Link to assembly instructions and more information


3-PFR-2031-AA-01 SeaMATE PufferFish ROV Kit (Rev 7) 1 kit
3-PFR-2033-AA-01 SeaMATE PufferFish Control Box Kit (Rev 7) 1 kit
1-BOX-1502-AA PufferFish Control Box Enclosure (w/ 4 Screws) 1 ea
1-BOX-1509-AA PufferFish Control Box Wrap Sticker 1 ea
1-MTR-3001-AC,AD,orAE Amp/Volt meter for PufferFish 1 ea
1-SWT-6203-AA DPDT Rocker Switch (splash-resistant) 4 ea
1-SRF-5501-AA FLEX Strain Relief Connector 3/8" (with Nut) 1 ea
1-SRF-5502-AA DOME Strain Relief Connector 3/8" 1 ea
1-SRF-5503-AA Strain Relief Connector Lock Nut 3/8" 1 ea
1-WKS-8227-AA 1/8" flathead screwdriver 1 ea
3-PFR-2035-AA-01 SeaMATE PufferFish Circuit Board Kit (Rev 7) (individual) 1 kit
1-PCB-3610-AA PufferFish Printed Circuit Board (Rev 7) 1 ea
1-MTR-3022-AA Amp/Volt meter instructions for PufferFish 1 ea
1-CPN-2305-AA Terminal Block - 2 Position (Green) 5mm 6 ea
1-CPN-2306-AA Terminal Block - 3 Position (Green) 5mm 1 ea
1-CPN-2501-AA Switch Connnectors 20 ea
1-CPN-2002-AA Bi-color LEDs (GRN/RED) 4 ea
1-CPN-2201-AA Resistor 10 ohm 3 ea
1-CPN-2203-AA Resistor 1k-ohm 4 ea
1-CPN-2101-AA Capacitor - Ceramic 1uf 100v 3 ea
1-CPN-2102-AA Capacitor - Aluminum 220 uf 25v 1 ea
1-CPN-2601-AA Radial Inductor 1 ea
1-CPN-2001-AA Diode 150V 2A 1 ea
3-PFR-2009-AA-01 SeaMATE AF/PF Motor and Propeller Kit 1 kit
1-THR-6504-AA Thruster Motor 3 ea
2-ZPV-4503-AA PVC Thruster/Camera mount 3 ea
3-PFR-2008-AB-01 SeaMATE AngelFish/PufferFish Propeller Kit 1 kit
1-THR-6501-AA Propeller 3 ea
1-FST-2702-AA Propeller Screw 3 ea
1-FST-2709-AA Locknut for propeller screw 3 ea
1-THR-6502-AA Propeller adapter 3 ea
1-FST-2701-AA Set screw for propeller adapter 3 ea
1-FST-2941-AA Thead locker (222MS purple, 0.5ml capsule) 1 ea
1-THR-6503-AA Hex wrench 1 ea
3-PFR-2011-AC-01 SeaMATE AF/PF Power Kit with Powerpole connectors 1 kit
1-PWR-5202-AA 10 Amp Fuse (Red) 1 ea
2-ZPW-7005-AC-01 30 Amp Powerpole Assembly Kit 1 kit
2-ZPW-4910-AA 30 Amp Bonded (Red/Black) Powerpole Connectors (red crimped to fuse holder, black crimped to zip cord) 1 assy
1-FST-2931-AA Velcro Closures 1 ea
1-WIR-7510-AA 7mm Black Heat Shrink 3 in
3-PFR-2012-AA-01 SeaMATE AF/PF Tether Kit 1 kit
1-WIR-7505-AA 18/6 AF/PF Tether Wire [feet] 25 ft
1-FST-2931-AA Velcro closures 1 ea
1-WIR-7508-AA 3/16" Red Heat Shrink tubing [inches] 12 in
1-WIR-7510-AA 7mm’ Black Heat Shrink [inches] 3 in
1-SRF-5602-AA DOME Strain Relief Connector 1/2" 2 ea
1-PVC-4501-AA PVC 1/2" Female slip adaptor 2 ea
2-ZPV-4508-AA 1/2 " PVC pipe (3.5 cm length) 2 ea
1-FST-2902-AA Zip Ties (small 4") 4 ea
1-PVC-4502-AA 1/2" PVC Cross 1 ea


Share this Product

More from this collection